SCHOOLAIR-B
Conforms to VDI 6022
Filter chamber cover
Water connection
Levelling foot
Ready-to-operate decentralised ventilation unit that provides good comfort levels and is used for the ventilation of internal spaces such as classrooms or conference rooms
Optional equipment and accessories
SEH Single room exhaust air
SRO Single room outdoor air
SRS Single room supply air
SET Single room extract air
SEC Single room secondary air
1 Outdoor air temperature sensor (optional)
2 Shut-off damper with actuator (outdoor air and exhaust air)
3 Fine dust filter ePM1
4 EC fans (supply air and extract air)
5 Recuperative heat exchanger
6 Sound attenuator
7 Heating coil
8 Cooling coil (optional)
9 Supply air temperature sensor (optional)
10 Bypass damper with actuator (modulating)
11 CO2 sensor (optional)
12 Extract air filter ISO coarse
Decentralised supply and extract air units ensure room ventilation. They dissipate the cooling loads and heat loads in accordance with the technical data.
An EC centrifugal fan takes in the fresh air which then flows through the motorised shut-off damper and the fresh air filter.
The fresh air then flows through the cross flow heat recovery unit and it can be switched off when it is sensible with regard to energy efficiency
and to protect the device..
If necessary, the air is heated or cooled by the heat exchanger before it is discharged to the room as a displacement flow (for 4-pipe systems, this is optional).
The extract air first passes through the fresh air filter, then flows through the heat recovery unit, the extract air fan and the motorised shut-off damper before it is discharged to the outside as exhaust air.
If the room air quality is sufficient, FSL-CONTROL III closes the outdoor air dampers and changes to secondary air operation, which is more energy efficient in any case.
Here, the control unit compares the target values of the indoor air quality with the actual values measured at the CO2sensor and switches automatically between fresh air and secondary air operation.
If the power fails, the fresh air and exhaust air dampers are closed to ensure fire protection and frost protection and to avoid draughts. This is ensured by a capacitor in each actuator.
The supply air is discharged near the external wall and with a medium velocity between 1.0 and 1.5 m/s. Due to the induction effect, the supply air velocity is rapidly reduced so that, in cooling mode, the supply air is discharged as a displacement flow over the entire floor area.
The convection from people and other heat sources causes the fresh air from the pool to rise and create comfortable conditions in the occupied zone.
| Width | 1590 mm |
| Height | 646 mm |
| Depth | 420 mm |
| Volume flow rate | 150, 200, 250 m³/h (boost 320 m³/h) |
| Nominal volume flow rate | 250 m³/h |
| Sound power level | 29 – 43 dB(A) |
Heat recovery efficiency | 60 % |
| Maximum operating pressure, water side | 6 bar |
| Maximum operating temperature | 75 °C |
| Supply voltage | 230 V AC ±10 %, 50/60 Hz |
| Power rating | 238 VA |
| Weight | 80 kg |
| SA-B | – | – | 4 | – | 1 | / | KR | / | 1590 × 646 × 420 | / | C3 | – | MA | – | T | / | MR | / | C | / | Z | / | A | / | HV | – | R | – | 0,40 | / | KV | – | R | – | 0,40 | |
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ||||||||||||||||||
| 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 | 17 | 18 | 19 |
No entry: Standard
3 Heat exchangerOrder example: SA-B-4-1-KR/1590×646×420/C3-MA-T/MR/C/Z/A/HV-R-0.40/KV-R-0.40
| Type | SA-B | horizontal decentralised sill ventilation unit X-CUBE/SCHOOLAIR-B |
| Variant | - | Standard |
| Heat exchanger | 4 | 4-pipe |
| Heat exchanger construction | 1 | Heat exchanger type 1 |
| Construction | KR | with condensate drain and water connection right |
| Nominal size [mm] | 1590×646×420 | Width 2100, height 750, depth 403 |
| Control | C3 | with FSL-CONTROL III |
| Control function | MA | Master |
| Real time clock | T | with real time clock |
| Interface | MR | with Modbus RTU |
| Air quality sensor | C | with CO2sensor |
| Supply air temperature sensor | Z | with supply air temperature sensor |
| Outdoor air temperature sensor | A | with outdoor air temperature sensor |
| Heating valve | HV | with thermoelectric actuator |
| Lockshield – heating circuit | R | with lockshield |
| kVS value – heating valve | 0.40 | 0.40 (straight-way valve) |
| Cooling valve | KV | with thermoelectric actuator |
| Lockshield – cooling circuit | R | with lockshield |
| kVS value – cooling valve | 0.40 | 0.40 (straight-way valve) |
Order example: SA-B-4-1-KR/1590×646×420/C3-SL/MT/Z/HV-R-0.40/KV-R-0.25
| Type | SA-B | horizontal decentralised sill ventilation unit X-CUBE/SCHOOLAIR-B |
| Variant | - | Standard |
| Heat exchanger | 4 | 4-pipe |
| Heat exchanger construction | 1 | Heat exchanger type 1 |
| Construction | KR | with condensate drain and water connection right |
| Nominal size [mm] | 1590×646×420 | Width 2100, height 750, depth 403 |
| Control | C3 | with FSL-CONTROL III |
| Control function | SL | Slave |
| Real time clock | - | - |
| Interface | MT | with Modbus TCP |
| Air quality sensor | - | - |
| Supply air temperature sensor | Z | with supply air temperature sensor |
| Outdoor air temperature sensor | - | - |
| Heating valve | HV | with thermoelectric actuator |
| Lockshield – heating circuit | R | with lockshield |
| kVS value – heating valve | 0.40 | 0.40 (straight-way valve) |
| Cooling valve | KV | with thermoelectric actuator |
| Lockshield – cooling circuit | R | with lockshield |
| kVS value – cooling valve | 0.25 | 0.25 (straight-way valve) |
Oldal megosztása
Oldal ajánlása
Oldal ajánlása, hivatkozás küldése e-mailben.
Oldal megosztása
Köszönjük, hogy ajánlott minket!
Ajánlását elküldtük és hamarosan meg kell érkeznie.
Kapcsolat
Hol tartózkodik Ön?
Adja meg üzenetét és kérése típusát
Tel.: +36 (1)212-1211 | Fax: +36 (1)212-0735
Kapcsolat
Köszönjük üzenetét!
Az üzenet elküldve, hamarosan feldolgozzuk. Szervizigényekkel foglalkozó részlegünk a lehető leghamarabb felveszi Önnel a kapcsolatot.
Általános, termékekkel, szolgáltatásokkal kapcsolatos kérdéseivel a következő telefonszámokon is fordulhat hozzánk:
Tel.: +36 (1)212-1211 | Fax: +36 (1)212-0735
Kapcsolat
Hol tartózkodik Ön?
Adja meg üzenetét és kérése típusát
Tel.: +36 (1)212-1211 | Fax: +36 (1)212-0735
Kapcsolat
Köszönjük üzenetét!
Az üzenet elküldve, hamarosan feldolgozzuk. Szervizigényekkel foglalkozó részlegünk a lehető leghamarabb felveszi Önnel a kapcsolatot.
Általános, termékekkel, szolgáltatásokkal kapcsolatos kérdéseivel a következő telefonszámokon is fordulhat hozzánk:
Tel.: +36 (1)212-1211 | Fax: +36 (1)212-0735
